• Welcome to World Machine Community. Please login or sign up.
September 17, 2019, 11:58:33 am


Read the Development Diary for an inside look at World Machine's progress!

15 Tips On How To Operate A Front End Loader Safely

Started by bestloaders, June 25, 2019, 06:25:24 pm

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.


As a widely used engineering construction machinery, the operation method of front end loader has become a serious topic. Especially we found that there are many construction site accidents because of the irregular operation method. So today, we will share 15 efficient tips on how to operate a front end loader safely. And we really hope to attract the attention of loader operators.
About learning front end loader operation
First of all, the most important significance of front end loader training is to ensure personal safety. According to accident search results from the Occupational Safety and Health Administration, the wrong or non-standard front end loader operation has killed many people. So how to use a front end loader has become a problem we can not ignore yet.
Secondly, we hope to improve the working efficiency of the loader through correct operation methods and maintenance.
Training manual we recommend
In fact, this article is based on many years of our experience in construction machinery manufacturing and maintenance. At the same time, we also refer to some professional wheel loader operator training manual.
Here are some resources to check out:
Front-End Loader Operator Toolkit
Front-End Loader Training
Front-End Loader Safety Tips
OJT: Front-End Loader Operation
Ok, Now Let's talk about how to use a front end loader together!
How to operate a front end loader safely?
#1: Before the loader starts normally, you should send out the necessary sound signals to warn pedestrians and other vehicles. At the same time, raise the bucket by 500mm from the ground. During driving, you should test the reliability of the brakes and avoid roadblocks or high voltage lines intentionally.
Most importantly, the front end loader does not take other personnel except the normal operator and absolutely disallow to carry people with the wheel loader bucket.
#2: When the front wheel loader is driving at high speed, you should keep the front-wheel drive. However, when it comes to low-speed scooping, you should operate it for four-wheel drive. In addition, it is important to avoid sudden steering and sharp turn or emergency braking after loading.
#3: In the process of the articulated wheel loaderwww.bestloaders.com is loading, you need to determine the loading amount according to the density of materials. On the other hand, the driver should lift the loader arm to turn the bucket and reduce the speed of action.
#4: The backhoe boom should be placed in the floating position to push the bucket smoothly when front end wheel loader is working on the loose and uneven site. However, if the backhoe boom moves up or down to the maximum limit, you must return the joystick to a neutral position.
#5: As a good operator, you should not push the handle too hard in any case. Similarly, you cannot descend the loader arm quickly when it is full of weight.
#6: Don't lift the bucket to the highest position to transport materials. Keep smooth of front end loader in the driving process.
#7: During carrying out loading or excavation, it is necessary to avoid partial loading of the bucket. After the bucket is full of material, you should lift bucket booms of the front end loader by 500mm from the ground before turning back to unload.
#8: Stop loading immediately wheel slip occurs because of large shovel loading resistance.
#9: Before unloading materials to the dump truck, it is advisable to reduce the unloading height.
#10: It is forbidden to touch the working part or overhaul under the loader is working. Before repairing the work device, descend it to the lowest position. At the same time, it is necessary to put some square timbers under the suspended part. In terms of maintenance, do not stand between the front and rear frame for related operations. Especially before the articulated wheel loader bogie is not locked.
#11: Unloading on the side slope, Keep the distance between the tire and the edge more than 1.5m. If the slope is greater than 30 degrees, do not unload with tip forward.
#12: The water temperature of internal combustion engine should not exceed 95 ℃ when it works. Meanwhile, torque converter oil temperature should be lower than 120 ℃.
#13: Stop operating the wheel loader immediately if any of the following occurs. For instance, the soil quality in the construction area is unstable, collapse, thunderstorm and flash flood.
#14: If the operator leaves the cab, land the bucket and shut off the engine, please.
#15: At the end of working, the operator should drive the wheel loader to a safe area. Then, put the bucket flat on the ground and the handle in the neutral position. Leave construction site after closing the door and window of the cab certainly.
Life for us or others is only once. Many accidents happen because we always think "No, it's impossible". Therefore, we must receive front end loader training before operating it. This is not only the professional requirement of the loader driver, but also our responsibility for families.
Now It's Your Turn
I hoped you enjoyed my suggestion on how to operate a front end loader safely.
Now I want to hear from you:
Which parts from this post are you most excited to know?
Are you going to know more about top 5 advantages of wheel loaders? Or do you want to do deep research on where to find the best wheel loader manufacturer?
Let me know by leaving a quick comment.

Quick Reply

With Quick-Reply you can write a post when viewing a topic without loading a new page. You can still use bulletin board code and smileys as you would in a normal post.

Note: this post will not display until it's been approved by a moderator.

Please leave this box empty:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:

Shortcuts: ALT+S save/post or ALT+P preview